We use cookies to enhance your experience. By continuing to browse this site you agree to our use of cookies. More info.

Polymers are high molecular mass molecules consisting of repeating units known as monomers that are linked by covalent chemical bonds. At the beginning of a batch type process the content of the reactor has a low viscosity and primarily consists of monomers. 

Once heat and/or a catalyst are introduced, the process of polymerization begins and viscosity becomes higher. Viscosity is an indirect way of quantifying the molecular mass of polymers.

Phenolic resins are commonly made for paper impregnation and gluing. They provide exceptional product features regarding material resistance and toughness, but the conditions of its production are challenging due to its reaction process.

Batches are never precisely the same because the range of ingredients are sourced from multiple suppliers. Every batch is weighed prior to mixing and then a reactor is used to heat them for a production cycle.

The viscosity and temperature of the solution are important parameters throughout this cycle. As the reaction is exothermic, heating will continue even after the heating process has stopped.

The heating process involves distinct phases and has highly sensitive viscosity and temperature values that must be monitored. If the resin becomes hard and a discrepancy arises, an unusable product is not the only consequence, but also possible damage to the reactors and pipes.

This results in significant wastage of raw material, lengthy downtime for complex maintenance, delivery delays, additional labor costs, and may require enormous replacement costs. 

The challenges related to viscosity in batch process polymerization are:

Installing an inline MIVI process viscometer provides simple observation of the endpoint of the polymerization reaction. It assists in the identification of the ideal temperature and viscosity parameters, and avoids mass solidification.

The Sofraser MIVI sensor can be simply installed:

The controller or electronics enables the operator to observe, in real-time, the temperature and viscosity values and to monitor safe and accurate batch process operations.

Figure 2. Onsite installation directly on the reactor wall.

Figure 3. Operation diagram of a MIVI sensor on a semi-batch MMA/MA solution copolymerization reactor system. Image Credit: School of Chemical Engineering and Institute of Chemical Processes, Seoul National University.

Thanks to its specific raw signal versus viscosity response the MIVI sensor offers a high degree of sensitivity at low viscosity combined with a very broad measurement range.

Figure 4. Response curve of a MIVI sensor for polymerization monitoring

This specificity allows the MIVI sensor to monitor the polymerization batch from the beginning to the end point.

This information has been sourced, reviewed and adapted from materials provided by SOFRASER.

For more information on this source, please visit SOFRASER.

Please use one of the following formats to cite this article in your essay, paper or report:

SOFRASER. (2020, April 01). Manufacturing Phenolic Resin. AZoM. Retrieved on June 18, 2022 from https://www.azom.com/article.aspx?ArticleID=19147.

SOFRASER. "Manufacturing Phenolic Resin". AZoM. 18 June 2022. <https://www.azom.com/article.aspx?ArticleID=19147>.

SOFRASER. "Manufacturing Phenolic Resin". AZoM. https://www.azom.com/article.aspx?ArticleID=19147. (accessed June 18, 2022).

SOFRASER. 2020. Manufacturing Phenolic Resin. AZoM, viewed 18 June 2022, https://www.azom.com/article.aspx?ArticleID=19147.

Do you have a question you'd like to ask regarding this article?

AZoM speaks with Joseph Toombs, a Ph.D. student at the University of California, Berkeley, about his research that has developed a new 3D printing process for the manufacture of small glass objects.

In this interview, AZoM talks to Jeanette Madigan from Mai Dubai about their water analysis, services and how Metrohm instruments impact their work.

James Tour & Kevin Wyss

AZoM spoke with Professor James Tour and Ph.D. candidate Kevin Wyss from Rice University about their research that has looked at upcycling disused car parts into high-quality turbostratic graphene.

This product profile outlines the MAX-iR FTIR Gas Analyzer from Thermo Fisher Scientific.

Learn more about the JAM-5200EBM E-Beam Metal Additive Manufacturing System for 3D Printing.

This product profile outlines the features and benefits of the Contour X - 500 3D Optical Profilometer.

AZoM.com - An AZoNetwork Site

Owned and operated by AZoNetwork, © 2000-2022